ZSOM

dac_4x16 - Seite überarbeitet (aus Schema V1.2, freigegeben)

claude (claude@undisclosed.example.com) — 2026-10-01T15:42:23+00:00

Analog Output The ZSOM-Control provides 4 analog outputs. They are generated by one DAC chip with 4 channels and an output stage for each channel. The ZSOM-Mini has no analog outputs. Features Parameter ZSOM-Control Number of channels 4 Resolution 16 bit Range ±10 V Update rate

adc_6x16 - Polarität ZSOM-Mini ergänzt (freigegeben)

claude (claude@undisclosed.example.com) — 2026-10-01T15:32:08+00:00

Analog Input The analog inputs of the ZSOM-Control and the ZSOM-Mini are grouped by ADC chips with 6 channels each. All channels of a group are sampled simultaneously and share the same input range. Features ZSOM-Control ZSOM-Mini Number of channels 12 (2 groups × 6)

mini_power_gpios - ADC RANGE Polarität korrigiert (freigegeben)

claude (claude@undisclosed.example.com) — 2026-10-01T15:32:08+00:00

ZSOM Mini Power and GPIOs On the ZSOM-Mini, individual board regions can be powered and reset separately. This is controlled via GPIO lines from the sbRIO-9651, so software can selectively enable, disable or reset specific parts of the system. By default, most board regions are disabled and must be activated by the application.

trouble_shooting - CAN-Treiber ergänzt (freigegeben)

claude (claude@undisclosed.example.com) — 2026-10-01T15:15:57+00:00

Trouble shooting Trouble Shooting Cheat Sheet Symptoms Possible Reason Mitigation Strategy Targets Power LED dark or Status LED dark when powered up Insufficient power supplied Check requirements The Status LED normally goes dark after a few secondsAll Target not woken up Activate through

can - Seite erweitert und neu strukturiert (freigegeben)

claude (claude@undisclosed.example.com) — 2026-10-01T15:15:57+00:00

CAN The ZSOM-Control and the ZSOM-Mini each provide one CAN (Controller Area Network) interface. It can be controlled from both FPGA and RT code; basic CANopen functions are available as RT VIs in the SDK. Features ZSOM-Control ZSOM-Mini Number of interfaces 1 1 Bit rate

rs422

ba (ba@undisclosed.example.com) — 2026-10-01T15:05:25+00:00

RS422 RS485 The ZSOM-Control and the ZSOM-Mini each provide one RS422/RS485 interface. By default it works as full-duplex RS-422 (4-wire); with two solder bridges or wiring at the terminals it can be used as half-duplex RS-485 bus (2-wire). Features ZSOM-Control ZSOM-Mini

rs485_rs422.png - created

ba (ba@undisclosed.example.com) — 2026-10-01T15:04:30+00:00

getting_started - Beispiele finden präzisiert (freigegeben)

claude (claude@undisclosed.example.com) — 2026-10-01T14:57:25+00:00

Quick start guide This document describes how to begin using the ZSOM-Control and ZSOM-Mini. What do You need to Get Started A ZSOM-Control Starter Kit or a ZSOM-Mini with power supply and USB-C cable Installing Software on the Host Computer Before using the ZSOM, you must install the following application software and device drivers on the host computer.

display - Getting started mit GUI-Beispiel (aus Supportanfrage, freigegeben)

claude (claude@undisclosed.example.com) — 2026-10-01T14:57:24+00:00

Display ZSOM-Control supports multi-touch displays. Simple examples are included in the SDK. ... Supported Displays * 5.7" 640x480px with capacitive multi touch * 3.5“ 320x240px with capacitive multi touch Features * Text * extendable font palette (see font generation for details) * Transparent or coloured background

rs232 - Seite erweitert (freigegeben)

claude (claude@undisclosed.example.com) — 2026-10-01T14:50:36+00:00

RS232 interface The ZSOM-Control and the ZSOM-Mini each provide one RS232 interface. It is based on a serial port of the sbRIO-9651 and an RS232 transceiver. Features ZSOM-Control ZSOM-Mini Number of interfaces 1 1 Signals TX, RX, RTS, CTS TX, RX Hardware handshake yes (

zsom_mini_versions

ba (ba@undisclosed.example.com) — 2026-09-29T15:40:02+00:00

ZSOM-Mini-Standard vs ZSOM-Mini-Embedded The ZSOM-Mini is available in two versions. Both have the same functionality and the same 56 signals (see pinout); they differ in how they are connected and mounted. * ZSOM-Mini-Standard: ready to use on its own, with screw terminals for direct wiring.

zsom-power-supply - Präzisiert: passt auf ZSOM-Mini-Standard

claude (claude@undisclosed.example.com) — 2026-09-29T15:38:07+00:00

ZSOM Power Supply The ZSOM Power Supply is a 12 V plug-in power supply with a pluggable screw terminal connector that fits directly into the power connector of ZSOM-Control and ZSOM-Mini-Standard. It is part of the ZSOM-Control Starter Kit and can also be ordered separately. Specifications Parameter

getting_started - Stromversorgung Standard/Embedded präzisiert

claude (claude@undisclosed.example.com) — 2026-09-29T15:38:07+00:00

ZSOM-Mini Quick start guide This guide is for users who have already made their first steps with the ZSOM-Control or the ZSOM-Control Starter Kit and now move their application to the ZSOM-Mini. It focuses on what is different on the ZSOM-Mini. This page is tailored for ZSOM-Mini-Standard boards. Some of the points may differ for

zsom_mini

ba (ba@undisclosed.example.com) — 2026-09-29T15:34:14+00:00

ZSOM-Mini The ZSOM-Mini is an off-the-shelf hardware module from NI Embedded-Specialty Alliance Member Schmid Elektronik, integrating the NI System-on-Module (SOM) sbRIO9651 on a tiny carrier board. It is designed for miniaturized measurement, control and monitoring applications and can be fully programmed with

ext_power - Steuersignale mit CLIP-Namen statt SOM-Pins (freigegeben)

claude (claude@undisclosed.example.com) — 2026-09-29T15:00:07+00:00

Switchable power supply The switchable power supply of the ZSOM-Control provides a 5 V and a 3.3 V output that can each deliver up to 300 mA. These outputs are intended to supply peripheral devices (e.g. sensors, small modules or external logic) whose supply voltage is switched on and off by the application running on the

kernel_update

ba (ba@undisclosed.example.com) — 2026-09-29T14:42:20+00:00

Kernel update instructions The modified kernel is available from GitHub: Release lwb5p/20.5-0.1 The instructions below perform a download directly onto the target. Preparation Before installing the kernel make sure the target has installed the following software. *

zsom-4g-gps-me909u-521 - Link auf Moduldokumentation (freigegeben)

claude (claude@undisclosed.example.com) — 2026-09-29T13:54:27+00:00

ZSOM-4G-GPS-ME909u-521 Status: in development. This plug-in is not yet directly supported by the ZSOM SDK. If you are interested, please contact Schmid Elektronik. The ZSOM-4G-GPS-ME909u-521 adds 4G/LTE mobile communication and GPS positioning to a ZSOM system. It is based on the ME909u-521

ordering_codes - Status 4G/GPS-RTK-Module: in development (freigegeben)

claude (claude@undisclosed.example.com) — 2026-09-29T13:54:26+00:00

Ordering Codes All ZSOM products Article Number Name Version Notes Product Status ZSOM-Control A020650 ZSOM-Control-Standard V1.2 Default configuration availableTBD ZSOM-Control-NoScrewTerminals V1.2 same as A020650 but without the screw terminals preliminaryA019305

zsom-gps-rtk-zed-f9r - Neue Produktseite (freigegeben)

claude (claude@undisclosed.example.com) — 2026-09-29T13:47:46+00:00

ZSOM-GPS-RTK-ZED-F9R Status: in development. This plug-in is not yet directly supported by the ZSOM SDK. If you are interested, please contact Schmid Elektronik. The ZSOM-GPS-RTK-ZED-F9R is a miniPCIe plug-in board for high precision positioning with dead reckoning. It carries the u-blox ZED-F9R module and plugs into the

zsom-gps-rtk-zed-f9p - Neue Produktseite (freigegeben)

claude (claude@undisclosed.example.com) — 2026-09-29T13:47:46+00:00

ZSOM-GPS-RTK-ZED-F9P Status: in development. This plug-in is not yet directly supported by the ZSOM SDK. If you are interested, please contact Schmid Elektronik. The ZSOM-GPS-RTK-ZED-F9P is a miniPCIe plug-in board for high precision positioning. It carries the u-blox ZED-F9P multi-band